Recommended first
Rectifying Graphene Seal haze
Follow the application plan below
Start by removing and evening out excess residue with a lightly damp cloth, followed by a dry buff.
ARTDESHINE DETAILING ACADEMY
Learn the care.
Understand the finish.
Practical car-care education, from your first safe wash to coating aftercare. Start with a lesson, or explore a method for the surface you’re working on.
Explore 12 lessons
Paint protection01 / 05
Your recommended routine
What should I do if Graphene Seal leaves patches or haze?
Start by removing and evening out excess residue with a lightly damp cloth, followed by a dry buff.
Recommended products: Two clean T2 cloths and clean water. No additional Graphene Seal is needed for this first step.
T2 Microfiber Cloth
Application plan
Use this method for fresh Graphene Seal residue on a cool surface, not cured coating high spots or etched damage.
- 1
Move into the shade and let the surface cool. If there is grit on the panel, wash it safely before wiping.
- 2
Lightly dampen one T2 with clean water and wring it out well; it should not drip.
- 3
Gently wipe one affected section to lift and spread out excess residue.
- 4
Immediately buff the same section using the second, clean, dry T2 until clear.
- 5
Turn to fresh cloth faces and repeat only as necessary. Do not spray more Graphene Seal onto the patch.
- 6
Inspect from different angles. If the mark remains, stop repeated rubbing and send the seller a clear photo for advice.
Final check: Patches can have different causes. A stain, scratch or cured coating defect needs its own assessment.
Follow the exact bottle and installer instructions for dilution, curing and surface compatibility.
Product application library
Understand each product’s role.
Learn when a product fits, how to use it and where its limits matter.
Graphene Seal
A focused finishing step for slickness and water beading after washing.
Simple usage
On clean, cool, dry, smooth paint, apply 2–5 light mists to a T2, spread thinly over about one square metre and buff with a second T2. Maintenance only: not a scratch, swirl or stain remover.
Bio Nano
Convenient wet-panel maintenance after washing. Spread, dry and buff — no rinse after application.
Simple usage
After washing and rinsing, keep paint cool and wet. Apply 3–4 light mists per square metre, spread with a clean wet T2, dry with a Drying Towel and final-buff with a clean dry T2. Do not rinse after application; follow the bottle.
Cleanse
A mild cleaner for interior surfaces and leather-care routines.
Simple usage
Test first. Apply Cleanse to a lightly damp T2, wipe compatible surfaces, collect dirt and residue with a clean damp cloth, then dry with a separate T2. Keep liquid out of vents and electronics.
Tyre Seal
Helps complete the detailed look with an even tyre-sidewall finish.
Simple usage
Apply to a clean, dry tyre sidewall with an applicator, spread evenly and allow 15–20 minutes to dry before driving.
Clarity
An abrasive polish for suitable unfilmed exterior-glass stains, after routine cleaning.
Simple usage
Check compatibility and test cool, unfilmed exterior glass. Follow the Clarity label with its soft applicator. Keep off mirrors, interior glass, tint and films; polishing may remove glass coatings.
Hybrid Plus
Professional paint-protection service for customers ready to move beyond DIY maintenance.
Simple usage
Book through an authorised installer for preparation and professional application.
Wheel Coat
Professional coating care dedicated to wheel surfaces.
Simple usage
Have the surface prepared and applied by an authorised installer.
Window Coat
Professional glass-protection service for a prepared window surface.
Simple usage
Have the glass assessed, prepared and applied by an authorised installer.
T2 Microfiber Cloth
A compact microfiber cloth for controlled application and final wiping.
Simple usage
Use separate clean sides for application and finishing to avoid wasting product.
Applicator Block
Helps distribute tyre and coating products evenly across the target surface.
Simple usage
Add a small amount of product and work methodically across the surface.
Leather Scrubber
Adds gentle mechanical cleaning action to a Cleanse interior routine.
Simple usage
Dampen first, apply Cleanse to the scrubber, work the area and wipe dry.
Artdeshine Mini Clay Cloth
Clay cloth is used to smoothen the car paint surface and glass surface. This is to remove fallouts, overspray and environmental pollutants that caused the paint surface become rough.
Simple usage
To use the clay cloth, the surface need to be wet.
Quick comparison
Bio Nano or Graphene Seal?
Both support regular car care, but they fit different application preferences.
Choose byBio NanoGraphene Seal
ApplicationWet panel: spread, dry and buff. No rinse.Dry panel: apply via cloth, then buff
Best fitFast wash maintenanceSlickness and beading
Use whenYou prefer wet-panel maintenanceYou want a focused finishing step
Installer foundations
Know when a method needs training.
Understand correction, coatings and aftercare, including when to stop and seek a practical assessment.
Explore the lesson